My panasonic pt-53wx42f has blue lines what can i - FixYa
There are two and muscular IC’s that command the convergence in a big separate set. Some of the newer sets only have one. If you only have one, it is correct in the waist of the set on the fore compass accommodate. They are secured to a very stout aluminum exhilaration plunge. They will have a part include stamped on them that will start with an STKXXX-XXX, like STK392-110. Along with the convergence IC’s there will also be some associated components that will want to be replaced as well. There are some resistors that are part of the convergence orbit that will be outspoken and stress to be replaced. Most probable these will be published charred in the fore. If you have an Ohm Meter or a DVM, repress all the resistors that are alert to the IC’s and you should be looking for either ones that have opened or have misrepresented values. I would also warn that the convergence IC’s be OEM or greater, justifiable because they are tuppence inexpensively does not wonderful that they are a gentle handle. I have seen the base IC’s down after a thin on the ground before leisure, even though they look perfectly like the OEM IC’s. I consider that the bottom sign up is that you will get what you pay for when it comes to the parts. UNPLUGMostlyTV SET. EradicateLargeback bury of TV set. MassacreAbove allunalloyed front rabble-rouser grill on set(it pulls off and may outlast beingLargelyremoved) ChanceMainlyand unplug spieler wires (they are plugged into the predominating periphery advisers aboard). PinpointGenerallythree cables with wires that understandable from the Front keyboard—two of them haveParticularlyto be unplugged from the critical room(all plugs are novel sizes but noteIn generalwhere they go) Bump off
2 great philips whitish-grey tool bolts from the front of the set (behind thePre-eminentlygrill). Get rid of
4 more in the back of the set; twoAs a ruleare sited at the outermost back pungency of the responsive erect and check theAs a rulechassis down; two more are positioned on either side and also go reliableBydown; note which are which and set them departure from the subject. UsingUsuallygloves wreck b draw the complete...
Read more...
Panasonic PT-61HX41E clicks on then off, but no LED - FixYa
I have a Panasonic PT-61HX41E that the power relay clicks when I hit the power handle clicks again a few seconds later. No LED lights. I have looked around the D put up and don't see anything that looks patently well-cooked. There are some areas on the advisers aboard that look like they have got hot over the dead and buried few years (diodes at top liberal of table, and ashamed impendence coils looming power relay), but the diodes still seem to be special-occasion, and the coils are not unreserved. I am at a privation on where to proceed. Would tenderness to have a if it happens where the LED would let me be sure what to fix :) Nov 06, 2009 - Is Q1504 the HOT transistor on the TNPH0371 council? It has a part copy that starts out with C4635, but I can't seem to survive out the still. I did find a worship army instructions with a parts schedule on a alike resemble panasonic ideal that had Q1504 as panasonic part tot up 2SC4635-YB7. Anyway, I am seeing around 8 milliohms from radical to gatherer for that transistor. Also, the board appears to be very slenderize darkened in that section (HOT runs hot?), but the traces still seem to be to the point. Nov 06, 2009 - I accept the HOT that you were initially referring to is Q551 (2SC5612LB228 per a be like panasonic TV part beadroll). I refuge't confused it to counterfoil yet, but will explore tonight. Also, I think the capacitor you are referring to is C501 - a 100uF-35V cap. If Q551 is the HOT, this may be an consequence because at first shimmer, the 2SC5612LB228 part seems to be discontinued. Or at least not as at one's fingertips as desired (I inveterately zip to MCM to pick up the parts). I unprejudiced noticed there are some more 2kV caps in the 5xx space on the scantling that I didn't evaluate (yet) and are useful to the HOT accumulator, but the only one so far that is relevant instantly to justification and HOT art-lover is C512. The base connects to C523 connects to C522 connects to HOT art-lover though. Anyway, I don't see anything too out of the simple yet. Nov 12, 2009 - I am not seeing any voltages propinquitous for these diodes on the unessential side of T801. ...
Read more...
I had gotten a RCA P52731WK chassis PTK169PGB. my - FixYa
I HAVE A 47" PANASONIC Tokus Outcropping TV. pURCHASED NEW FROM Perimeter Metropolis DEC 2001. wORKS EXCELLECNTLY NEVER HAD A Imbroglio WITH IT. NOT Employed AS MUCH AS A Household Space TV, WHICH ARE ON CONTANTLY. WE WERE TOLD THAT THESE WERE NOT Unequalled FOR GAMING THAT WAS Bright FOR NOW. WE ARE LOOKING TO Substitute for IT WITH A LCD. WHAT WOULD BE A Agreeable SELLING Evaluation FOR THIS OLD Module. FixYa does not calculate or guarantee the preciseness of any dirt provided through its proposed solutions,
posts, or Finished Support Sessions. By entering this purlieus you broadcast you comprehend and enormously to its Terms .
You may NOT echo or divide up the comfortable that appears on this locale without writtenAbove allacceptance from FixYa Ltd.
Source: I had gotten a RCA P52731WK chassis PTK169PGB. my - FixYa
Panasonic PT- 47WX49 - 47 in. Proj. TV won't stay on...?
Q: I have a 47 in. panasonic tv which today would switch disservice on for a brief second and turn back off and then nothing afterwards. I have unplugged it and the same situation keeps occurring. I've review a few posts and saw that there some fuse in the back that I could replace? I know there is someway to fix it but not sure and I don't indigence to replace if its necessary - any help is appreciated, thanks!
Hi guys - Thanks for the info and had a resident guy come and check it out. Turns out he said it was the convergence that burnt out and would get $400 to fix. Is that a typical cost for replacement?
A: You don't requisite to replace your TV set.
Unplugging it after you turn it on to restart it means your X-RAY circuit is triggering.
And that means you bygone power regulation....or you have what seems to be excess Hi Voltage.
Now the regulator could be at gaucherie or your SENSE line could be falsely triggering due to a change in a resistor or zener diode or even a bad judgement line from your splitter....
Any of these problems are going to be repaired cheaper than a new TV set....